- 您现在的位置：买卖IC网 > Sheet目录1210 > DLP-USB232R (DLP Design Inc)MODULE USB-TO-SRL UART 18-DIP
CBitBangI/O
BitBangWRn
BitBangRDn
CBUS0, CBUS1, CBUS2, CBUS3
CBUS0, CBUS1, CBUS2, CBUS3
CBUS0, CBUS1, CBUS2, CBUS3
CBUS bit-bang mode
option. Allows up to four of
the CBUS pins to be used
as general purpose I/O.
Configured individually for
CBUS0, CBUS1, CBUS2
and CBUS3 in the internal
EEPROM. [A separate
Application Note (AN232R-
01, available from the FTDI
website (www.ftdichip.com)
describes in more detail
how to use the CBUS
bit-bang mode.]
Synchronous and
asynchronous bit-bang
mode WR# strobe output.
Synchronous and
asynchronous bit-bang
mode RD# strobe output.
* PWREN# should be used with a 10k-ohm resistor pull-up.
** When in USB Suspend Mode, the output clocks are also suspended.
1.0 QUICK START GUIDE
Note: This guide requires the use of a Windows 98/2000/Vista PC that is equipped with a
USB port.
1. Download the CDM drivers from either www.dlpdesign.com or www.ftdichip.com . Unzip
the drivers into a folder on the hard drive.
2. Select a power source for the DLP-USB232R. The typical configuration for an all 5-volt
system is to connect Pins 7, 8 and 9.
3. Connect the DLP-USB232R module to the host PC via a USB-A to Mini-B cable. This action
initiates the loading of USB drivers. When prompted, select the folder where the CDM
drivers were stored in Step 1. Windows will then complete the installation of the device
drivers for the DLP-USB232R module. The next time the DLP-USB232R module is
attached, the host PC will immediately load the correct drivers without any prompting.
Reboot the PC if prompted to do so.
At this point, the DLP-USB232R is ready for use.
Rev. 1.0 (November 2008)
6
? DLP Design, Inc.
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
DLP-USB245M-G
MODULE USB-TO-TTL PARL FIFO CONV
DLP-USB245R
MODULE USB-TO-PARL FIFO 18-DIP
DM163001
BOARD DEMO PICDEM-1
DM163004-LT
BOARD DEMO PICDEM.NET
DM163005
KIT EVAL PIC16C432/433 LIN BUSS
DM163007
PICDEM CAN-LIN 1 FOR 18C658/858
DM163008
KIT MCP2120/2150 FOR IRDA COMM
DM163010
BOARD DEMO PICDEM USB
相关代理商/技术参数
DLP-USB245M
功能描述:界面模块 USB-FIFO Adapter
RoHS:否 制造商:4D Systems 产品:Serial Converters 通道/端口数量: 数据速率: 接口类型:USB, UART 工作电源电压:3.3 V, 5 V 最大工作温度:
DLP-USB245M-G
功能描述:界面模块 USB-FIFO Adapter
RoHS:否 制造商:4D Systems 产品:Serial Converters 通道/端口数量: 数据速率: 接口类型:USB, UART 工作电源电压:3.3 V, 5 V 最大工作温度:
DLP-USB245R
功能描述:界面模块 USB-TO-PARALLEL FIFO INTERFACE MODULE
RoHS:否 制造商:4D Systems 产品:Serial Converters 通道/端口数量: 数据速率: 接口类型:USB, UART 工作电源电压:3.3 V, 5 V 最大工作温度:
DLP-UT1
功能描述:工业温度传感器 TEMPERATURE SENSOR RoHS:否 制造商:Texas Instruments 准确性:1 C 功能:Temperature Sensing 25 摄氏度时的电阻: 温度范围:- 55 C to + 127 C 电源电流: 电源电压:2.7 V to 5.5 V
DLP-UTH8
功能描述:数据记录与采集 DLP SENSOR HUB
RoHS:否 制造商:Lantronix 描述/功能:Analog device server 显示器类型:None 电流额定值:
DLPVA-100-F
制造商:未知厂家 制造商全称:未知厂家 功能描述:Low Frequency Voltage Amplifier
DLPVA-100-F-D
制造商:未知厂家 制造商全称:未知厂家 功能描述:Low Frequency Voltage Amplifier
DLPVA-100-F-S
制造商:未知厂家 制造商全称:未知厂家 功能描述:Low Frequency Voltage Amplifier